Trailer Axles and Axle Repair Parts at Freeway Trailer Sales

ID 008-091-05

1 of 5

008-091-05 2200lb 4 on 4" Bolt Pattern Idler Hub

Dexter 8-091-5 idler hub fits 1250lb to 2200lb capacity axles and has a 4 on 4" bolt pattern. Compatible all with BT(1" bearing combination) or BTR(1-1/16" bearing combination) style E-Z Lube, Sure-Lube, Accu-Lube, Super Lube, Easy Grease and non lubing spindles. Interchangeable with all major trailer axle brands. This hub has a 5-1/2" diameter flange for use with 8", 10", and 12" trailer wheels.

1 - Small face Idler hub with 4 on 4" lug bolt pattern (see image on how to measure lug spacing)
- 5-1/2" diameter flange
- 4-1/8" overall height
- 1/2"-20 thread pitch lug studs
- has a 1.98" bore diameter
- Rated 1100 lbs. capacity per side(bearing size dependent)
2 - L44610 bearing races (pre-installed)

This trailer idler hub is interchangeable with all industry standard axle brands including Dexter Axle, Lippert Components (LCI), Rockwell American, AL-KO, Axle Tek, TK Trailer Axles, UFP by Dexter Marine, Tie Down by Dexter Marine, and C.E. Smith.

For use with 8", 10" or 12" wheels

Please note: This hub is not to be used on 13" or larger wheels.

Price$31.99

ID 008-259-05

1 of 5

008-259-05 2200lb 5 on 4-1/2" Bolt Pattern Small Flange Idler Hub

Dexter 8-259-5 Small flange idler hub fits 1250lb to 2200lb capacity axles and has a 5 on 4-1/2" bolt pattern. Compatible all with BT(1" bearing combination) or BTR(1-1/16" bearing combination) style E-Z Lube, Sure-Lube, Accu-Lube, Super Lube, Easy Grease and non lubing spindles. Interchangeable with all major trailer axle brands. This hub has a 5-1/2" diameter small flange for use with 8", 10", and 12" trailer wheels.

1 - Small face Idler hub with 5 on 4-1/2" lug bolt pattern (see image on how to measure lug spacing)
- 5-1/2" diameter small flange
- 4-1/8" overall height
- 1/2"-20 thread pitch lug studs
- has a 1.98" bore diameter
- Rated 1100 lbs. capacity per side(bearing size dependent)
2 - L44610 bearing races (pre-installed)

This trailer idler hub is interchangeable with all industry standard axle brands including Dexter Axle, Lippert Components (LCI), Rockwell American, AL-KO, Axle Tek, TK Trailer Axles, UFP by Dexter Marine, Tie Down by Dexter Marine, and C.E. Smith.

For use with 8", 10" or 12" wheels

Please note: This hub is not to be used on 13" or larger wheels.

Price$31.99

ID RVI-U-5450

1 of 4

RVI-U-5450 3500lb 5 on 4-1/2" Bolt Pattern Idler Hub

TRP TruRyde import RVI-U-5450 idler hub fits 2990lb to 3500lb capacity axles and has a 5 on 4-1/2" bolt pattern. Compatible all with 1-1/16" inner diameter outer bearing and a 1-3/8" inner diameter inner bearing combination style E-Z Lube, Sure-Lube, Accu-Lube, Super Lube, Easy Grease and non lubing spindles. Interchangeable with all major trailer axle brands.

1 - Idler hub with 5 on 4-1/2" lug bolt pattern (see image on how to measure lug spacing)

6-1/4" diameter flange
4-1/8" overall height
1/2"-20 thread pitch lug studs
1 - L44610 outer bearing race (pre-installed)
1 - L68111 inner bearing race (pre-installed)
has a 1.98" bore diameter
Rated 1750 lbs. capacity per side

This trailer idler hub is interchangeable with all industry standard axle brands including Dexter Axle, Lippert Components (LCI), Rockwell American, AL-KO, Axle Tek, TK Trailer Axles, UFP by Dexter Marine, Tie Down by Dexter Marine, and C.E. Smith.

Price$33.99

ID TR4104

1 of 4

TR4104 2200lb 5 on 4-1/2" Bolt Pattern Large Flange Hub Kit with 1" Bearing Set

Import TR4104 idler hub kit fits 1250lb to 2200lb capacity axles and has a 5 on 4-1/2" bolt pattern. Compatible all with BT(1" bearing combination) style E-Z Lube, Sure-Lube, Accu-Lube, Super Lube, Easy Grease and non lubing spindles. Interchangeable with all major trailer axle brands. This hub has a 6-1/4" diameter large flange for use with 10", 12", 13", 14" and 15" trailer wheels.

Kit includes:

1 - Idler hub with 5 on 4-1/2" lug bolt pattern (see image on how to measure lug spacing)
- 6-1/4" diameter flange
- 4-1/8" overall height
- 1/2"-20 thread pitch lug studs
- Rated 1100 lbs. capacity per side
2 - L44643 bearings
- 1" (1.000") inner diameter
2 - L44610 bearing races (pre-installed)
1 - 12192TB Grease seal (see note for alternate seal option)
- 1.249" inner diameter
- 1.987" outer diameter
1 - 1.98" outer diameter lube style cap and rubber plug
5 - 1/2"-20 thread pitch zinc plated 60 degree coned lug nuts

For use with 10", 12", 13", 14" and 15" wheels. This hub will not work on 8" wheels

This trailer idler hub is interchangeable with all industry standard axle brands including Dexter Axle, Lippert Components (LCI), Rockwell American, AL-KO, Axle Tek, TK Trailer Axles, UFP by Dexter Marine, Tie Down by Dexter Marine, and C.E. Smith.

Please note: This kit is not pre-greased or pre-assembled as this hub set can also fit trailer axles that have a grease seal inner diameter of 1.500" part #010-009-00. If ordering for this seal size please let us know in the order comments and we will swap out the seal in the kit for the correct size at no additional charge.

Price$33.99

ID TR4106

1 of 4

TR4106 2200lb 5 on 4-1/2" Bolt Pattern Large Flange Hub Kit with 1-1/16" Bearing Set

Import TR4106 idler hub kit fits 1250lb to 2200lb capacity axles and has a 5 on 4-1/2" bolt pattern. Compatible all with BTR(1-1/16" bearing combination) style E-Z Lube, Sure-Lube, Accu-Lube, Super Lube, Easy Grease and non lubing spindles. Interchangeable with all major trailer axle brands. This hub has a 6-1/4" diameter large flange for use with 10", 12", 13", 14" and 15" trailer wheels.

Kit includes:

1 - Idler hub with 5 on 4-1/2" lug bolt pattern (see image on how to measure lug spacing)
- 6-1/4" diameter large flange
- 4-1/8" overall height
- 1/2"-20 thread pitch lug studs
- Rated 1100 lbs. capacity per side
2 - L44649 bearings
- 1-1/16" (1.063") inner diameter
2 - L44610 bearing races (pre-installed)
1 - 10-9 Grease seal (see note for alternate seal option)
- 1.500" inner diameter
- 1.987" outer diameter
1 - 1.98" outer diameter lube style cap and rubber plug
5 - 1/2"-20 thread pitch zinc plated 60 degree coned lug nuts

For use with 10", 12", 13", 14" and 15" wheels. This hub will not work on 8" wheels

This trailer idler hub is interchangeable with all industry standard axle brands including Dexter Axle, Lippert Components (LCI), Rockwell American, AL-KO, Axle Tek, TK Trailer Axles, UFP by Dexter Marine, Tie Down by Dexter Marine, and C.E. Smith.

Please note: This kit is not pre-greased or pre-assembled as this hub set can also fit trailer axles that have a grease seal inner diameter of 1.250" part #12192TB. If ordering for this seal size please let us know in the order comments and we will swap out the seal in the kit for the correct size at no additional charge.

Price$33.99

ID 16272

16272 2.32" Chrome Bearing Protector with Bra Set

16272 2.32" Chrome Bearing Protector with Bra - Sold as a pair

Why use a Bearing Protector?

Boat trailer hubs get warm while traveling to the ramp. Warm hubs backed into cool water during launching are suddenly cooled which contracts any air inside the hub creating a vacuum. The vacuum pulls water and road grit inside the hub contaminating the grease. The contamination causes corrosion and rapid wear. Perfectly good bearings can be ruined in less than one season.

Bearing Protectors corrects this problem by filling the entire hub with grease. Most air that is trapped inside the hub will be expelled by the Bearing Protector pressure relief feature. Once the hub is full, the spring loaded piston in the Bearing Protector exerts a slight pressure to the grease inside the hub. With the pressure inside the hub slightly higher than the pressure outside the hub, water and grit cannot be drawn inside.

An automatic pressure relief feature prevents over-filling the hub which would damage seals.

Fits hubs with an inner diameter of 2.32"
Chrome Plated

Sold as a pair

Price$36.99

ID 16273

16273 2.44" Chrome Bearing Protector with Bra Set

16273 2.44" Chrome Bearing Protector with Bra - Sold as a pair

Why use a Bearing Protector?

Boat trailer hubs get warm while traveling to the ramp. Warm hubs backed into cool water during launching are suddenly cooled which contracts any air inside the hub creating a vacuum. The vacuum pulls water and road grit inside the hub contaminating the grease. The contamination causes corrosion and rapid wear. Perfectly good bearings can be ruined in less than one season.

Bearing Protectors corrects this problem by filling the entire hub with grease. Most air that is trapped inside the hub will be expelled by the Bearing Protector pressure relief feature. Once the hub is full, the spring loaded piston in the Bearing Protector exerts a slight pressure to the grease inside the hub. With the pressure inside the hub slightly higher than the pressure outside the hub, water and grit cannot be drawn inside.

An automatic pressure relief feature prevents over-filling the hub which would damage seals.

Fits hubs with an inner diameter of 2.44"
Chrome Plated

Sold as a pair

Price$36.99

ID TR4108

1 of 4

TR4108 3500lb 5 on 4-1/2" Bolt Pattern Hub Kit with 1-1/16" and 1-3/8" Bearing Set

Import TR4108 idler hub kit fits 2990lb to 3500lb capacity axles and has a 5 on 4-1/2" bolt pattern. Compatible all with 1-1/16" inner diameter outer bearing and a 1-3/8" inner diameter inner bearing combination style E-Z Lube, Sure-Lube, Accu-Lube, Super Lube, Easy Grease and non lubing spindles. Interchangeable with all major trailer axle brands.

Kit includes:

1 - Idler hub with 5 on 4-1/2" lug bolt pattern (see image on how to measure lug spacing)
- 6-1/4" diameter flange
- 4-1/8" overall height
- 1/2"-20 thread pitch lug studs
- Rated 1750 lbs. capacity per side
1 - L44649 bearing
- 1-1/16" (1.063") inner diameter
1 - L68149 bearing
- 1-3/8" (1.378") inner diameter
1 - L44610 outer bearing race (pre-installed)
1 - L68111 inner bearing race (pre-installed)
1 - 171255TB Grease seal (see note for alternate seal option)
- 1.719" inner diameter
- 2.565" outer diameter
1 - 1.98" outer diameter lube style cap and rubber plug
5 - 1/2"-20 thread pitch zinc plated 60 degree coned lug nuts

This trailer idler hub is interchangeable with all industry standard axle brands including Dexter Axle, Lippert Components (LCI), Rockwell American, AL-KO, Axle Tek, TK Trailer Axles, UFP by Dexter Marine, Tie Down by Dexter Marine, and C.E. Smith.

Please note: This kit is not pre-greased or pre-assembled as this hub set can also fit trailer axles that have a grease seal inner diameter of 1.687" part #168255TB. If ordering for this seal size please let us know in the order comments and we will swap out the seal in the kit for the correct size at no additional charge.

Price$37.99

ID 10BRKLH

1 of 3

10BRKLH 10" X 2-1/4" Left Hand Standard Electric Brake Assembly

This is a LEFT SIDE brake assembly. Reduce precious time and aggravation on difficult brake repairs by using this easy to install complete brake assembly kit. These CSA certified kits provide durability, and reliability in braking performance. Used on 3500LB axles. Sold individually.

Used on drivers side of trailer

Identified by green wire on the magnet

Better Braking – Automotive grade friction material molded to brake shoes.
Linings are fully bonded to shoes for long life and more braking torque.
Cut linings instead of snapped offers less chance of cracking and crumbling.
E-coated backing plate resists wear and corrosion.
10" x 2-1/4" rated at 3,500 lb. capacity - per axle.
Left Hand.

Direct interchange for the following brands and part numbers:

HuskyTow - 30793

TRP-TruRyde - BK-10E-01

Ultra-Fab - 48-979110

Ultra-Fab - 48-979150

AP Products - 014-122258

AP Products - 014-122258-B

Price$45.99

ID 10BRKRH

1 of 3

10BRKRH 10" X 2-1/4" Right Hand Standard Electric Brake Assembly

This is a RIGHT SIDE brake assembly. Reduce precious time and aggravation on difficult brake repairs by using this easy to install complete brake assembly kit. These CSA certified kits provide durability, and reliability in braking performance. Used on 3500LB axles. Sold individually.

Used on passenger side of trailer

Identified by green wire on the magnet

Better Braking – Automotive grade friction material molded to brake shoes.
Linings are fully bonded to shoes for long life and more braking torque.
Cut linings instead of snapped offers less chance of cracking and crumbling.
E-coated backing plate resists wear and corrosion.
10" x 2-1/4" rated at 3,500 lb. capacity - per axle.
Right Hand.

Direct interchange for the following brands and part numbers:

HuskyTow - 30794

TRP-TruRyde - BK-10E-02

Ultra-Fab - 48-979111

Ultra-Fab - 48-979151

AP Products - 014-122450

AP Products - 014-122450-B

Price$45.99